First...

After my remote mentors got the lesson through on how to sharpen my bowl gouges, of course I had to try and turn a bowl. I chucked a small piece of maple on, and managed to get things into round...

So far so good...


I continued on, however this morning... and it was looking pretty good. I had it fairly smooth inside, I sanded it to 220 and everything.

Then I turned it around on the chuck, padded the chuck with some paper towel and expanded the jaws into the bowl. Had I simply removed the foot, and left it at that, all would have been well.

So I sighed, pulled it off of the chuck & signed it. 

South wall solar project musings

Warts and all, here is the south face of my shop. 

 I've let it weather 'naturally' for far too long, and since my ladder phobia kicked in, I've never put the siding on it that it deserves.

My neighbors to the south of me have recently taken down 4 maple trees, so I'm now going to get a ton more sun on the shop year round. I don't mind it in the fall and winter, but summers are going to be annoying.

I'm ultimately going to make the  best of things, and I'm finally going to make the solar wall on this face.

First off, Dyami, I have lots of Tyvek left, and I'll be adding that across the entire face.
Next, I'm going to face my fears, and put up more of the tan T-111 on the top 4' of the building. I"d like to do the pallet siding, but the T-111 is already on hand. I have a window opening framed out on the upper section.

Looking at that photo, the doorway is 6' wide and 8' tall. I'm planning on making a solar wall that will be from the 10' line all the way across and framing the doorway opening.

I'm not sure about the doorway yet. I've been sketching some ideas, currently I want to make a Dutch Door and a side light. I'm thinking a full 4' wide with the side light on the right side. (pardon the crude photoshop doodle).

My newfangled bench is currently on that wall, but I'm thinking of re-arranging the shop a bit, and moving the lathe up to the front of the shop instead. To paraphrase Alton Brown, "but that's another post" #GoodEats

That will give me 60 sf of solar collection. I could go all the way up to the eaves, however I'd lose the heat from the upper section, as it would be above the drop ceiling.






Another option altogether is to simply make the entire south wall into a solar collector, and move the entrance over to the West wall. I have a doorway framed in already roughly where the red frame is here:

I wouldn't eliminate the door on that wall, simply turn each half of the door into a smaller collector, adding to the overall gain. I would still make a larger collector where the green squiggles are, and just build new doors which would in effect be solar panels in and of themselves. 

What say ye faithful readers? 

edit:

Dyami asked about my solar plans, well I'm going simple with a design based on info found on http://www.builditsolar.com

I've been planning on a wall similar to what this link shows. I'm considering adding an additional seasonal lean-to similar to this.  I have a Bunch of 4" black flex hose, I'm thinking of punching several 4" holes through in the 'doorway' space for this year, with a solar powered duct fan pulling the heated air into the shop. I figure I can put a 4x8 sheet of OSB and/or foil backed insulation on the bottom, (raised off of the ground) build a simple lean to from roughly the right edge of the window over to the right edge of the building. I'll tack some roofing felt on the side of the building for the winter, that, plus the black hose, and some plastic sheeting and I should get some additional 'free' heat. You can see the box items just below the window, that was a small scale attempt from last fall, which brought a Little heat in, but not enough to warrant putting it back together again.

The solar wall on the south face, Plus the tent/lean to heater will hopefully allow me to woodwork deeper into the winter months if not all the way through the winter, unless we have another bout with arctic conditions for weeks on end like we had this past year.

A Big Thank you is due

Hi folks, I'd like to extend a big Thank You to several of my friends. I almost posted 'online' friends, then I decided that Friends are Friends, and online simply means I haven't met them in person yet.

I've been making a concerted effort to use my lathe more lately.  I've owned it for almost 10 years, and have never really taken the plunge into the vortex.  Naturally enough, turning is a very short hobby if one doesn't learn to sharpen the tools.

Well, I recently got a new grinder, and I realized that I had done a number on my two bowl gouges before I set up my grinder and the wolverine jig

There it is under the old 6" grinder. (note to self, take photo of the Snazzy new grinder and the wolverine...)









Over the years, I've done my best to learn from my friends who turn, and have been honored to meet several important folks in the turning 'world'.

One of the nicest and most respected gentlemen I've had the pleasure to meet and learn from is Bill Grumbine.  I posted a quick video on a facebook group that he has.   I very quickly had several good replies with advice on how to repair the gouges. 

Bill was  even nice enough to share a clip he made on how to  over come my errors, as was my friend Stu in Tokyo! 

My friend Vaughn also chimed in with input on how to recover the grind. 

Guys, I am pleased to announce that with your collective help, I'm well on my way to fixing the troubled grinds:

1/2" bowl gouge with repaired fingernail grind

1/2" V-gouge with repaired fingernail grind.

Here are pics to prove I'm getting there.
 Bill saw these on the facebook group page, and offered a further tip, I'll be putting that to use in the morning and I'll call them fixed! Now to learn how to use them on a piece of wood!



Shameless plug, if you're a turner looking to learn how to turn a bowl, Check out both of Bill's Superb DVDs:

'Turned Bowls Made Easy' & 'Beyond the Basic Bowl'. He can be found online at wonderfulwood.com 

OK time for a shop tour

I've been writing nearly two months about my time in my shop, but for the most part I've avoided posting photos of the inside, mostly because I'm embarrassed by the clutter. I'm horrible about keeping things neat and tidy in my shop. However I did a bit of a brush up yesterday, so here goes.

A reminder, my shop is only 12'x20' so this will be quick:

This is from the far end, looking back at the south end of my shop. On the left you can see my newfangled clutter collector. workbench. on the right there in the corner is an old tambour door mag tape storage cabinet. I have shelving in there and some of my clutter is festering there.
Just in front of the cabinet is my Harbor Freight 14" bandsaw with riser kit, and just in front of that is my Shopsmith DC3300 dust collector.

 And here is the view to the north end of the shop (where the siding is going up). Sharp eyed viewers will notice a window on the inside, but none on the outside. I was given a window, and it is framed in, but not sealed, so I haven't cut through and finished the install. oh well.

In the distance is my Delta Midi lathe, left corner has my shorts/turning blank storage tower, just before that is my other clutter collection, er Bench with my Delta benchtop drill press. Yeah, as you can see, I'm running off of extension cords still... one tool and a light at a time.  Lumber storage is on the east wall, my jointer lives under that and my rolling Ultimate Tool Stand is currently in front of that.  Just overhead above the UTS is a lumber and stuff rack which both hangs from the Loft rafters and the east wall of the shop. It only looks low, I can easily walk underneath it and it is 2' of vertical storage. for those concerned about it failing, it's held up for 6 years so far, I don't see it going anywhere soon.

 Looking up, you can see the home made trussses and the loft section of the shop. Lord only knows what's up there anymore, I haven't been up there in years. (remember that whole ladder thing...)
 The top sill of my side walls is 10' up, and the floor of the loft is a 2x8 above that. The loft joists primarily keep the walls from bowing out, at least until I build the ships ladder I've been planning.

 The green insulation is going to be my drop ceiling this winter. I'm going to close off the loft area, bringing the ceiling height down to a mere 10' or so.

There's my favorite power tool as I have mentioned before Circa 2001 or 2002 (whenever the Borg sold off all of their Emerson built Ridgid saws) It still works great, and has been through a lot.










No, I'm not going to focus on the clutter, until I get rid of more of it.

There's the back of last years attempt at a solar collection system. I'm about to rip that out and make a new entry to the shop. Look for that in the next month or so. Fall is fast approaching and I have big plans for Solar Heat in my shop this year.

In the meantime, I have a quickee clamp rack, and a couple of table saw jigs up on the wall.

 There's the 'tool wall' to the right of where my table saw lives. The dovetail jig is one I picked up from someone on LumberJocks (where I rarely go since they went so over the top ad intensive but that's another post). I think I overpaid when I gave him $25 for it. Rockler or whichever. I've never used it, and probably won't.
Below that is my small crosscut sled, on the right is my other clamp rack.
The 'first tool' I ever put in the shop is just below the dovetail jig, an el cheapo pencil sharpener.

 this is one of two pieces of shop art

that's a close up of the other piece, made of cutting board blank 'ends'. I was batching them out earlier this year, and came across several pieces of cherry marked with the name of the piece:

20" Cherry

That ought to be enough for now. I've got several plans for the shop in the coming weeks and months. And The holidays are fast approaching, I"ll be making loads of cutting boards, and several shop additions/upgrades before the snow flies. 

 Thanks for looking. Please leave a comment below!

Spoon! complete with video...

I had this spoon blank rough cut and sitting up on my gouge rack above my lathe, silly me, I chose the hardest darned maple I could find. Not a bad thing on the Lathe, but carving out the bowl was a bit of a chore.

Here is a shot of it on the lathe, under power

The handle's just a spindle, the Bowl however is a propeller.


Here it is stopped.

Several years ago I bought myself a spoon plane (currently AWOL on my bench somewhere) and then some time after that I picked up a hook knife:

I was pleasantly surprised how quickly I roughed out the bowl of this spoon. It looks Hand done, as indeed it should.

The chunk of maple I carved this out of turned out to be ambrosia maple, complete with beetle tracks. That makes this an art project now, not a working spoon.


And here's a short clip showing the spoon under power on the lathe: